|
Similiar Products
B & C Eagle 97/25 1-Inch 20 Gauge 3/16-Inch Crown Staple for S3297-LHF (5,000 per Box)
Our Price $9.95
Porta-Nail 42620 Flooring Nail/Staple Setting Tool
Our Price $13.79
Stanley Bostitch #SB97-1GLS Hardwood Floor Staple
Our Price $24.80
Fein MultiMaster FMM 250Q Top
Our Price $399.00
Hardwood Floors: Laying, Sanding and Finishing
Our Price $8.99
|
|
Bostitch LHF97125-2 Floor Runner Laminated Hardwood Flooring Stapler for 1/4-inch to 1/2-inch Flooring
|
Enlarge Image
|
List Price $280.00
Our Price $230.00
You Save $50.00 That's 18% off |
|
See new offers for as low as $220.00 from 11 sources
See used offers for as low as $189.99 from 2 sources
|
|
The Bostitch LHF97125-2 20-gauge laminated hardwood flooring stapler is designed for the installation of 1/4- to 1/2-inch laminated tongue and groove flooring. For speed and accuracy, the LHF97125-2 has a tool-free adjustable-foot that adapts from 1/4- to 1/2-inch engineered flooring. By using 1/2- to 1-inch, 3/16-inch crown 20-gauge staples, it helps prevent damage to the flooring. Its lightweight magnesium design adds durability and its oil-free operation requires no regular maintenance and eliminates the risk of oil stains. Bostitch designed this tool specifically for laminated tongue and groove flooring and backs it with its exclusive 7-year warranty, but always check with flooring manufacturer's fastening recommendations before starting the job. |
Features
- Laminated hardwood pneumatic flooring stapler for 1/4-inch to 1/2-inch flooring
- Tool-free adjustable base; ultra-quiet rear exhaust
- Magnesium housing for extreme durability; molded rubber grip
- Tapping block-included
- 10.13 by 8.25 by 3-inches; 2-1/2-pounds; 7-year limited warranty
|
Great Tool
Great tool right out of the box. But do yourself a favor and get the Bostitch staples !!!
Great and Easy To Use Tool
I bought this after giving up being on a waiting list two weeks to rent one from a local hardware store. Glad I bought it. Not only is it a great tool and easy to use, but since I don't have to worry about returning a rental, I can take my time on the installation. I had never done this before, but it's been very easy installing the 3/8 engineered flooring I purchased for our remodel. I've put in about 800 square feet without any problems. Even my 9 year old son has had no problems operating this tool. If you are going install new 3/8" hardwood, save yourself a samll fortune by buying one of these and doing it yourself.
Nice Product
Product arrived on time and in great condition. I am installing Brazilian Teak which is extremely hard. The gun has had a couple of mis-fires which were likely user error combined with the fact that this is extremely hard wood. This gun feels like it is a product designed to be a quality product meant to be used everyday. At the same time, the mag body allows it to be lightweight.
A quality tool for professionals
The main cause of malfunction for this kind of tool is the user's air compressor. Either it isn't drained regularly, isn't set to the proper pressure, or isn't sufficient to use this tool. Those are the primary reasons for the described malfunctions. This is a first rate nailer for those who use quality equipment and maintain it properly.
Buying this product without knowing the availability of the staples is an amateur mistake. Don't knock the product because of it. Those of us who use these tools for a living know that they need maintainence from time to time. The weekend warrior who bought and returned 3 of these to use with his cheapo compressor should weigh his time/money against the cost of hiring a profesional.
It works but has some problems.
It will staple engineered flooring down but be prepared for more than a few bent and twisted staples. Unless you apply heavy pressure against the flooring the bent staples will damage the edge and you will need to remove it. Perhaps I have a lemon and you will have better luck than I did. Hope it works better for you than it did for me.
|
|
|
|